Friday, November 24, 2017

Scaps and Bridal Tulle to make a Quilt Background.



I liked the image of the boots with leaves that I made for the SAQA Benefit Auction a few years back, so I decided to use the same design to make larger version.

The boots are made from fabric that I hand-dyed.  My actual boots are brown, but I hate brown and love purple.  To get the variation in color that I hoped would look like light reflecting off wet boots, I used the low-water immersion process with Procion dyes from Dharma.  Low-water immersion dyeing produces lots of variation in color throughout the fabric. I love that.

The leaves are fused on, as are the toes of the boots using Misty Fuse.

To get the bright blue stripes along the toe of the boots, I used Derwent  INKtense color blocks.  If you dampen the fabric, color it with the INKtense, and then heat set it with a hot iron, it is supposed to be color fast.  That certainly seems to be the case.  I never wash my quilts, but just hanging on walls, the InkTense colors I've used on other quilts seem to have maintained their rich. bright hues over the years.

I wanted a background that looked like grass, but that didn't detract from the boots.  I tried a number of "grassy" fabrics, but....yuck.  I finally settled on using a jillion slivers of scraps--mostly green, but also yellow, purple and beige.  To make the scraps skinny enough to look like grass,  I piled them on my cutting mat, and ran over them a million times with my rotary cutter.  Then I cut the fabric for my quilt backing--about 6 inches bigger all around than I intended my quilt to be, and I laid a piece of batting about the same size over that, heaped the scraps on the batting. The batting helped hold the scraps in place kind of like Velcro.

Next I layered a piece of black tulle over the whole background and pinned it in place about every two inches in all directions, and solidly along the edges so all those little pieces wouldn't fall out.   Stuff still tumbled out when I moved the piece to the sewing machine, but I just kept stuffing the scraps back in, and putting more pins in place. (the boots were NOT attached at this point.) I quilted the piece very tightly, as you can see in the photo below.  The lines of random quilting are about a quarter inch apart.

After stitching all those fraying little scraps between the tulle and batting, my sewing machine needed a MAJOR cleaning.

(NOTE:  that skinny little yellow trim on the toe of the boot is actually about an inch wide, but only an 1/16th to 1/8th inch or so is peeking out from the blue piece layered over it.   That is really the only way to manage small sliver-y accent pieces.)




Once the background was stitched, I added the boots and pant legs, quilted them in place, and as my British husband would say, Bob's your uncle.  Then this piece joined the cue to await binding, a hanging sleeve, and a label.  Sigh.  Old habits die hard.


Sunday, November 19, 2017

Glue, Fusibles, or Pins? That is the Question

Putting together a collaged quilt can be done in many ways.  Before sections make their way to the sewing machine everything has to be held together in some way.  There are those who swear by glue, others who use pins--thousands of pins like the amazing Merle Axelrad , and still others who are devotees of fusibles.  I have tried them all.

For me, glue wins the prize--and not just any glue, but Elmer's Washable School Glue.

I have tried glue sticks, and Aleene's Tacky Glue, but Elmer's School Glue--NOT regular Elmer's--works best for me.    I found glue sticks way too messy, and Aleene's Tacky Glue way too sticky.  When Aleene's Glue sets it is there to stay, which can be a good thing, but I change my mind a lot.  I need something that holds all those little pieces  together, but that can be pulled apart without fraying or distorting the fabric.

Also, if I accidentally splodge glue in the wrong places--which I'm prone to do, Aleene's makes pretty permanent shiny spot, but Elmer's can be sponged off pretty easily.  I've heard that Elmer's School glue is not glue so much as a thickened starch, which is what makes it washable.

large section held together with glue only.
The piece hanging on my design wall is about a third of my quilt and at this point, only Elmer's glue is holding it together.  

small squeeze bottle with very small metal tip, sold by Amazon
Heat setting the glue is what makes it work.   I put a thin line of glue on the edge of the fabric (thinner than can be made with the bottle of glue itself) and I heat set it with a hot iron.

I bought this little bottle with the great nozzle on Amazon for a couple bucks.  I've been using it a couple years and it seems up to the task.  Some times I have to run a straight pin down the spout to clear out the dried glue, but that's the only issue I've ever had with it.  I like the control, and as you can see it takes very little glue to hold things securely.

I have tried using lots of different fusibles--Wonder Under, Misty Fuse, Soft Fuse, and found them all to be a pain in the neck.  Once you press fusible down, it is DOWN.  You will not be pulling that piece off without a disaster.  I've tried to not press anything until I had all my little pieces where I was sure I wanted them, but then I needed a million pins to keep things in place, which distorted the fabric, and made it harder to keep everything flat.  FLAT is what I want most. 

ALSO, as I pinned and moved the construction around, I wrinkled it.  YIKES! It's not FLAT!   So I'd press it without thinking...and attach hours of my work to my ironing board cover. Grrrr.

School Glue is made for fools like me.  It's easy to use, holds when you need it to, ease enough to take apart if needed, and can be cleaned up with water, plus it's cheap and available literally everywhere.